Yearbooks

Programme: BEng (Chemical Engineering) ENGAGE

Kindly take note of the disclaimer regarding qualifications and degree names.
Code Faculty Department
12136002 Faculty of Engineering, Built Environment and Information Technology Department: Chemical Engineering
Credits Duration NQF level
Minimum duration of study: 5 years Total credits: 691 NQF level:  08

Programme information

Please note: The Engineering Augmented Degree Programme (ENGAGE) is an extended degree programme with a five-year curriculum. It is designed to enable students who show academic potential but who do not meet the normal entry requirements for the four-year degree programme, to obtain an Engineering degree. ENGAGE students spend the first three years of the programme covering the content of the first two years of the four-year degree programme. They also take compulsory augmented modules in each of the Level 1 subjects. These augmented modules provide students with background knowledge and skills needed to succeed in an engineering degree. The curriculum for years four and five of the ENGAGE programme are identical to the curriculum for years 3 and 4 of the 4-year programme, respectively. Students may apply directly for admission to the programme.

  • Students must register for the entire programme, not components of it. The curriculum is fixed; there are no electives.
  • Attendance at all components of years 1 to 3 of the programme is compulsory. Non-attendance will only be condoned in the case of illness (sick note required) or family crisis (e.g. a death in the family), in which case students must inform the programme administration immediately.
  • Students who fail to meet the attendance requirement for any module in any semester of years 1 to 3 of the programme will be excluded from the programme.
  • No augmented module may be repeated more than once.
  • Selection into the programme will be based on a combination of performance in the National Senior Certificate examinations or equivalent and other selection tests approved by the faculty.
  • A student who fails a mainstream module (e.g. Chemistry) but passes the associated augmented module (e.g. Additional chemistry) does not need to repeat the augmented module.
  • A student who fails an augmented module (e.g. Additional chemistry) but passes the associated mainstream module (e.g. Chemistry) does not need to repeat the mainstream module.
  • A student must meet the attendance requirement and obtain at least 40% for both the continuous assessment and test components as well as a final mark of 50% in order to pass an augmented module.
  1. The curricula of the fourth and the fifth years of study are identical to those of the third and the fourth years of the four-year programme.
  2. JPO 110 is a prerequisite for JPO 120. Credit for JPO is obtained with a final mark of more than 50%. Conditional admission to JPO 120: If the final mark for JPO 110 is between 45% and 49%, a student can register for JPO 120 but credit for JPO 110 and JPO 120 will only be obtained if the final combined mark for JPO 110 and JPO 120 is above 50%.

Please note: All students will be required to successfully complete JCP 203, Community-based project 203, as part of the requirements for the BEng degree. A student may register for the module during any of the years of study of the programme, but preferably not during the first or the final year of study.

Learning outcomes of the BEng degree:
A graduate in engineering should be able to apply the following skills on an advanced level:

  1. Engineering problem solving.
  2. Application of specialist and fundamental knowledge, with specific reference to mathematics, basic sciences and engineering sciences.
  3. Engineering design and synthesis.
  4. Investigation, experimentation and data analysis.
  5. Engineering methods, skills, tools and information technology.
  6. Professional and general communication.
  7. Awareness and knowledge of the impact of engineering activity on society and the physical environment.
  8. Work in teams and in multidisciplinary environments.
  9. An awareness and ability for lifelong learning.
  10. An awareness and knowledge of principles of professional ethics and practice.
  11. Awareness and knowledge of engineering management principles and economic decision-making.

Learning contents of the BEng programmes:
Six essential knowledge areas are included in the syllabi of the programmes. The typical representation of each knowledge area as a percentage of the total contents of an undergraduate programme is given in brackets ( ) in the list below. This percentage varies for the different study directions, but conforms in all instances to the minimum knowledge area content as stipulated by ECSA.
Knowledge areas:

  1. Mathematics, including numerical methods and statistics (13%)
  2. Basic sciences: the natural sciences essential to the programme (15%)
  3. Engineering sciences (40%)
  4. Engineering design and synthesis (16%)
  5. Computing and information technology (5%)
  6. Complementary studies: communication, economy, management, innovation, environmental impact, ethics, engineering practice (11%).

Admission requirements

Important information for all prospective students for 2022

  • The admission requirements apply to students who apply for admission to the University of Pretoria with a National Senior Certificate (NSC) and Independent Examination Board (IEB) qualifications.
  • Applicants with qualifications other than the abovementioned should refer to:
    • Brochure: Undergraduate Programme Information 2022: Qualifications other than the NSC and IEB, available at click here.
  • Citizens from countries other than South Africa (applicants who are not South African citizens) should also refer to:
  • School of Tomorrow (SOT), Accelerated Christian Education (ACE) and General Education Development Test (GED): The University of Pretoria no longer accepts qualifications awarded by these institutions.
  • National Certificate (Vocational) (NCV) Level 4: The University of Pretoria may consider NCV candidates, provided they meet the exemption for bachelor’s status criteria and the programme requirements.

Transferring students

A transferring student is a student who, at the time of application for a degree programme at the University of Pretoria (UP) –

  • is a registered student at another tertiary institution, or was previously registered at another tertiary institution and did not complete the programme enrolled for at that institution, and is not currently enrolled at a tertiary institution, or has completed studies at another tertiary institution, but is not currently enrolled at a tertiary institution, or has started with tertiary studies at UP, then moved to another tertiary institution and wants to be readmitted at UP.

A transferring student will be considered for admission based on

  • an NSC or equivalent qualification with exemption to bachelor’s or diploma studies (whichever is applicable); and meeting the minimum faculty-specific subject requirements at NSC or tertiary level; or having completed a higher certificate at a tertiary institution with faculty-specific subjects/modules passed (equal to or more than 50%), as well as complying with faculty rules on admission;
  • previous academic performance (must have passed all modules registered for up to the closing date of application ) or as per faculty regulation/promotion requirements;
  • a certificate of good conduct.

Note: Students who have been dismissed at the previous institution due to poor academic performance, will not be considered for admission to UP.

Returning students

A returning student is a student who, at the time of application for a degree programme –

  • is a registered student at UP, and wants to transfer to another degree at UP, or was previously registered at UP and did not complete the programme enrolled for, and did not enrol at another tertiary institution in the meantime (including students who applied for leave of absence), or has completed studies at UP, but is not currently enrolled or was not enrolled at another tertiary institution after graduation.

A returning student will be considered for admission based on

  • an NSC or equivalent qualification with exemption to bachelor’s or diploma studies (whichever is applicable); and meeting the minimum faculty-specific subject requirements at NSC or tertiary level; or previous academic performance (should have a cumulative weighted average of at least 50% for the programme enrolled for);
  • having applied for and was granted leave of absence.

Note: Students who have been excluded/dismissed from a faculty due to poor academic performance may be considered for admission to another programme at UP.  The Admissions Committee may consider such students if they were not dismissed more than twice. Only ONE transfer between UP faculties will be allowed, and a maximum of two (2) transfers within a faculty.

Important faculty-specific information on undergraduate programmes for 2022

  • The closing date is an administrative admission guideline for non-selection programmes. Once a non-selection programme is full  and has reached the institutional targets, then that programme will be closed for further admissions, irrespective of the closing date. However, if the institutional targets have not been met by the closing date, then that programme will remain open for admissions until the institutional targets are met.
  • The following persons will be considered for admission: Candidates who have a certificate that is deemed by the University to be equivalent to the required National Senior Certificate (NSC) with university endorsement; candidates who are graduates from another tertiary institution or have been granted the status of a graduate of such an institution, and candidates who are graduates of another faculty at the University of Pretoria.
  • Life Orientation is excluded when calculating the APS.
  • Grade 11 results are used for the conditional admission of prospective students.
  • A valid qualification with admission to degree studies is required.
  • Minimum subject and achievement requirements, as set out below, are required.
  • Admission to ENGAGE in the School of Engineering will be determined by the NSC results, achievement levels of 5 for Mathematics, Physical Sciences and English, and an APS of 30.
  • Students may apply directly to be considered for the ENGAGE programme. 
  • All modules will be presented in English, as English is the language of tuition, communication and correspondence.

Note: Our programmes are accredited by the Engineering Council of South Africa (ECSA), and our degrees meet the requirements for Professional Engineers in SA.

University of Pretoria website: click here

Minimum requirements

Achievement level

English Home Language or English First Additional Language

Mathematics

Physical Sciences

APS

NSC/IEB

NSC/IEB

NSC/IEB

5

5

5

30

Promotion to next study year

Promotion to the second semester of the first year and to the second year of study 

  1. A new first-year student who has failed in all the prescribed modules of the programme at the end of the first semester, is excluded from studies in the School of Engineering. A student who is registered for the Engineering Augmented Degree Programme and has passed only 8 credits will also be excluded.
  2. A student who complies with all the requirements of the first year of study, is promoted to the second year of study.
  3. A student who has not passed at least 70% of the credits of the first year of study after the November examinations, must reapply for admission should he/she intend to proceed with his/her studies. Application on the prescribed form must be submitted to the Student Administration of the School of Engineering not later than 11 January. Late applications will be accepted only in exceptional circumstances after approval by the Dean. Should first-year students be readmitted, conditions of readmission will be determined by the Admissions Committee.
  4. Students who have not passed all the prescribed modules at first-year level (level 100), as well as students who are readmitted in terms of Faculty Regulations must register for the outstanding first-year level (level-100) modules.
  5. A student who is repeating his or her first year, may, on recommendation of the relevant heads of department and with the approval of the Dean, be permitted to enrol for modules of the second-year of study in addition to the first-year modules which he or she failed, providing that he or she complies with the prerequisites for the second-year modules and no timetable clashes occur. Students on the ENGAGE programme may, following the same procedure, be permitted to enrol for level-200 modules in addition to the level-100 modules which he/she failed providing that he/she complies with the prerequisites for the modules at 200-level and no timetable clashes occur. On recommendation of the relevant head of department and with special permission from the Dean, permission may be granted to exceed the prescribed number of credits. The total number of credits which may be approved may not exceed the normal number of credits per semester by more than 16 credits.
  6. Students in Computer, Electrical and Electronic Engineering, who fail a first-year module for the second time, forfeit the privilege of registering for any modules of an advanced year of study.


Please note:

  1. From the second year of study each student should be in possession of an approved calculator. It is assumed that each student will have easy access to a laptop computer.
  2. Students who intend transferring to Mining Engineering, must familiarise themselves with the stipulations set out in the syllabi of PWP 121 Workshop practice 121.


Promotion to the third year of study of the Four-year Programme, as well as to the third and the fourth years of study of the ENGAGE Programme. In case of the fourth year of study of the ENGAGE Programme, the words "first", "second" and "third" must be substituted with the words "second", "third" and "fourth" respectively. 

  1. A student who complies with all the requirements of the second year of study, is promoted to the third year of study.
  2. A student must pass all the prescribed modules at first-year level (level 100) before he or she is admitted to any module at third-year level (level 300).
  3. A student who is repeating his or her second year must register for all the second-year modules still outstanding. Such a student may, on recommendation of the relevant head of department and with the approval of the Dean, be permitted to enrol for modules of the third year of study in addition to the second-year modules which he or she failed, providing that he or she complies with the prerequisites for the third-year modules and no timetable clashes occur. On recommendation of the relevant head of department, and with special permission from the Dean, permission may be granted to exceed the prescribed number of credits. The total number of credits which may be approved may not exceed the normal number of credits per semester by more than 16 credits.
  4. Students in Computer, Electrical and Electronic Engineering who fail a second-year module for the second time forfeit the privilege of registering for any modules of the third year of study.
  5. Students who intend transferring to Mining Engineering must familiarise themselves with the stipulations set out in the syllabi of PWP 120 Workshop practice 120, as well as PPY 317 Practical training 317.


Promotion to the fourth year of study of the Four-year Programme, as well as to the fifth year of study of the ENGAGE Programme. In case of the fifth year of study of the ENGAGE Programme, the words "second", "third" and "fourth" must be substituted with the words "third", "fourth" and "fifth" respectively.

  1. A student who complies with all the requirements of the third year of study is promoted to the fourth year of study. A student who does not comply with all the requirements but who is able to register for all outstanding modules in order to complete the degree programme, may at registration be promoted to the fourth year of study.
  2. A student must pass all the prescribed modules of the second year of study, before he or she is admitted to any module of the fourth year of study.
  3. A student who has not passed all the prescribed modules of the third year of study, must register for the outstanding modules. A student may be admitted by the Dean, on the recommendation of the relevant head of department, to modules of the fourth year of study, in addition to the outstanding third-year modules, provided that he or she complies with the prerequisites of the fourth-year modules and no timetable clashes occur. The total number of credits per semester for which a student registers may not exceed the normal number of credits per semester by more than 16 credits. In exceptional cases, the Dean may, on recommendation of the relevant head of department, permit a student to exceed the above limit.
  4. Students in Computer, Electrical and Electronic Engineering who fail a third-year module for the second time, forfeit the privilege of registering for any modules of the fourth year of study.

Pass with distinction

  1. A student graduates with distinction if:
  1. no module of the third or fourth year of study of the four-year programme or of the fourth or fifth year of the ENGAGE programme was repeated and a weighted average of at least 75% (not rounded) was obtained in one year in all the modules of the final year of study; and
  2. the degree programme was completed within the prescribed four years for the four-year programme and within the prescribed five years of the ENGAGE programme.
  1. Exceptional cases to the above will be considered by the Dean.

Minimum credits: 129

Fundamental modules

Core modules

  • Module content:

    General introduction to inorganic, analytical and physical chemistry. Nomenclature of inorganic ions and compounds, stoichiometric calculations concerning chemical reactions, redox reactions, solubilities and solutions, atomic structure, periodicity. Molecular structure and chemical bonding using the VSEPR model. Principles of reactivity, electrochemistry, energy and chemical reactions, entropy and free energy.
    Appropriate tutorial classes and practicals.

    View more

  • Module content:

    Introductory mathematics: Symbols, exponents, logarithms, angles in degrees, radial measure, goniometry, differentiation, and integration. Motion along a straight line: position and displacement, acceleration. Vectors: adding vectors, components, multiplying vectors. Motion in two and three dimensions: projectile motion, circular motion. Force and motion: Newton’s Law, force, friction. Kinetic energy and work: work, power. Potential energy: Centre of mass, linear momentum. Collisions: impulse and linear momentum, elastic collisions, inelastic collisions. Rotation: kinetic energy of rotation, torque.  Oscillations and waves: Simple harmonic motion, types of waves, wavelength and frequency, interference of waves, standing waves, the Doppler effect. Temperature, heat and the first law of thermodynamics.

    View more

  • Module content:

    Social sciences: Perspectives on contemporary society
    An introduction to long-standing questions about the nature of human societies and contemporary challenges. Topics to be discussed include globalisation and increasing connectedness; rising unemployment, inequality and poverty; rapid urbanisation and the modern city form; transformations in the nature of work; environmental degradation and tensions between sustainability and growth; shifts in global power relations; the future of the nation-state and supra-national governance structures; and possibilities for extending human rights and democracy. Critical questions are posed about modern selfhood, sociality, culture and identity against the background of new communications technologies, ever more multicultural societies, enduring gender, class and race inequities, and the emergence of new and the resurgence of older forms of social and political identity. These issues are approached from the vantage of our location in southern Africa and the continent, drawing on social science perspectives.

    View more

  • Module content:

    Humanities: Text, culture and communication
    Successful communication of ideas, values and traditions depends on understanding both the literal and implied meanings of texts. In this module students are introduced to a variety of texts, including original literary and visual texts, with a view to developing an understanding of how textual meanings have been constructed and negotiated over time. Students are encouraged to understand themselves as products of – and participants in – these traditions, ideas and values. Appropriate examples will be drawn from, among others, the Enlightenment, Modernism, Existentialism, Postmodernism and Post-colonialism.

    View more

  • Module content:

    A project-based approach is followed to equip students wiuth academic and IT skills to succeed within the School of Engineering at UP.

    View more

  • Module content:

    Background knowledge, problem-solving skills, conceptual understanding and chemical reasoning skills required by CHM 171/172.

    View more

  • Module content:

    Background knowledge, problem-solving skills, conceptual understanding and mathematical reasoning skills required by WTW 158.

    View more

  • Module content:

    A project-based approach is followed to equip students with academic and IT skills to succeed within the School of Engineering at UP.

    View more

  • Module content:

    Background knowledge, problem-solving skills, conceptual understanding and physical reasoning skills required by FSK 116/176.

    View more

  • Module content:

    Background knowledge, problem-solving skills, conceptual understanding and mathematical reasoning skills required by WTW 164.

    View more

  • Module content:

    *This module is designed for first-year engineering students. Students will not be credited for more than one of the following modules for their degree: WTW 158, WTW 114, WTW 134, WTW 165.
    Introduction to vector algebra. Functions, limits and continuity. Differential calculus of single variable functions, rate of change, graph sketching, applications. The mean value theorem, the rule of L'Hospital. Indefinite integrals, integration.

    View more

  • Module content:

    *This module is designed for first-year engineering students. Students will not be credited for more than one of the following modules for their degree: WTW 146, WTW 148 and WTW 124,

    Vector algebra with applications to lines and planes in space, matrix algebra, systems of linear equations, determinants, complex numbers, factorisation of polynomials and conic sections. Integration techniques, improper integrals. The definite integral, fundamental theorem of Calculus. Applications of integration. Elementary power series and Taylor’s theorem. Vector functions, space curves and arc lengths. Quadratic surfaces and multivariable functions.

    View more

  • Module content:

    *Attendance module only
    The module is offered at the end of the first year of study and lasts at least eight days, during which training is given in the following workshops: electronic projects, panel wiring, electrical motors and switch gear, general machines, welding, turning and sheet metal work. Each student's progress is assessed after each workshop.

    View more

Minimum credits: 136

Core modules

  • Module content:

    One quarter general physical-analytical chemistry: Physical behaviour of gases, intermolecular forces, solutions, liquids and solids (phase changes), chemical equilibrium, acids and bases, applications of aqueous equilibria (e.g. buffers, titrations, solubility) precipitation. One quarter organic chemistry: Structure and bonding, functional groups and drawing of structures of organic compounds, nomenclature, isomerism, introductory stereochemistry, introduction to chemical reactions and chemical properties of organic compounds. Appropriate tutorial classes and practicals. Quality theoretical and practical teaching with an ethical approach provides a broad understanding of fundamental chemistry, e.g. predicting the behaviour of specific functional groups present in organic compounds, essential for new drug development, purification of mixtures and proper waste management to protect the environment and ultimately human and animal life, thereby meeting some of the UN sustainable development goals.

    View more

  • Module content:

    Dimensions, units and their conversion. The mol unit, density, concentration. Specific volume, bulk density, density of ideal mixtures. Temperatures and conversions. Pressure, absolute and gauge. Expression of concentration. Empirical formulae. Introduction to material balances: strategy for solving problems. Material balances without chemical reaction. Combinations of equipment.

    View more

  • Module content:

    Chemical reaction and stoichiometry, excess reactant, conversion, yield, selectivity. Material balances with recycle streams, bypass streams and purge streams. Gases, vapours and liquids: ideal gas law, SG and density of gases, Nm³. Material balances where gases are involved. Fuels and combustion: coal analysis, combustion calculations.

    View more

  • Module content:

    The general objective of this module is to develop expertise in solving electric and electronic circuits. The topics covered in the course are Ohm's law, Kirchoff's current and voltage laws, voltage and current division, mesh current and node voltage methods, linearity, Thevenin and Norton equivalent circuits, source transformation, power transfer, energy storage elements in circuits (inductors and capacitors), and operational amplifiers and applications. Although circuits will mostly be solved using direct current (DC) sources, the final part of the course will consider methods to solve circuits using alternating current sources (AC).

    View more

  • Module content:

    This module is integrated into all undergraduate academic programmes offered by the Faculty. Main objectives: execution of a community project aimed at achieving a beneficial impact on a section of a socio-economically underprivileged community located in socio-economically deprived areas our society; awareness of personal, social and cultural values and an understanding of social issues; and development of life skills.

    View more

  • Module content:

    Background knowledge, problem-solving skills, conceptual understanding and reasoning skills required by EBN 111/122.

    View more

  • Module content:

    Background knowledge, conceptual understanding, drawing skills and reasoning skills required by MGC 110.

    View more

  • Module content:

    Background knowledge, problem-solving skills, conceptual understanding and chemical reasoning skills required by CHM 181.

    View more

  • Module content:

    Background knowledge, problem-solving skills, conceptual understanding and reasoning skills required by SWK 122.

    View more

  • Module content:

    Freehand sketching covering the following: perspective, isometric and orthographic drawings. Drawing conventions, graphical techniques and assembly drawings. Evaluation of drawings and error detection. True lengths of lines, projections and intersections. Practical applications of these techniques. Introduction to computer-aided drawings, including dimensioning, crosshatching and detailing. Introduction to basic manufacturing processes including primary (casting, forging and extrusion) and secondary (drilling, turning, milling, grinding, broaching and sawing) manufacturing procedures.

    View more

  • Module content:

    Equivalent force systems, resultants. Newton's laws, units. Forces acting on particles. Rigid bodies: principle of transmissibility, resultant of parallel forces. Vector moments and scalar moments. Relationship between scalar- and vector moments. Couples. Equivalent force systems on rigid bodies. Resultants of forces on rigid bodies. Equilibrium in two and three dimensions. Hooke's law. Trusses and frameworks. Centroids and second moments of area. Beams: distributed forces, shear force, bending moment, method of sections, relationship between load, shear force and bending moment.

    View more

  • Module content:

    Calculus of multivariable functions, directional derivatives. Extrema. Multiple integrals, polar, cylindrical and spherical coordinates. Line integrals and the theorem of Green. Surface integrals and the theorems of Gauss and Stokes.

    View more

  • Module content:

    Numerical integration. Numerical methods to approximate the solution of non-linear equations, systems of equations (linear and non-linear), differential equations and systems of differential equations. Direct methods to solve linear systems of equations.

    View more

Minimum credits: 136

Core modules

  • Module content:

    Engineering systems are often subjected to variation, uncertainty and incomplete information. Mathematical statistics provides the basis for effectively handling and quantifying the effect of these factors. This module provides an introduction to the concepts of mathematical statistics and will include the following syllabus themes: data analysis, probability theory, stochastic modelling, statistical inference and  regression analysis.

    View more

  • Module content:

    Organic chemistry. Chemical properties of organic (including aromatic) compounds. Functional group transformation and synthesis.

    View more

  • Module content:

    Theory: Introduction to instrumental chemical analysis. Integration of electronic, chemical, optical and computer principles for the construction of analytical instrumentation. Detail discussion of principles and some instrumental methods from three disciplines within analytical chemistry, namely electrochemistry, spectroscopy and chromatography. This includes potentiometry, (AA) atomic absorption-, (ICP) atomic emission-, ultraviolet (UV)-, and infrared (IR) spectroscopy, potentiometric and photometric titrations, gas chromatography, liquid chromatography as well as combinations of these techniques. Practical: IR spectroscopy, UV spectroscopy, AA spectroscopy, potentiometric titration, gas chromatography.

    View more

  • Module content:

    Introduction to the synthesis, processing, structure, physical properties, and technical performance of important engineering materials: metals, ceramics, polymers and composites. Structural, mechanical, thermodynamic, and design related issues important to chemical engineering applications. Materials specification with emphasis on the corrosion of metals and life time estimation for polymer components.

    View more

  • Module content:

    Vapour pressure, phase changes, equilibrium. Vapour/gas equilibrium; Henry’s law. Enthalpy and enthalpy balances. Heat of reaction. Data and data sources, steam tables. Enthalpy and combustion; flame temperature. Heats of solution and mixing. Miscible and immiscible liquid mixtures; dew point, bubble point. Simultaneous mass and enthalpy balances. PVT properties of real gases, PVT-diagrams of pure compounds. Vapour liquid equilibrium for ideal mixtures (Raoult's law).

    View more

  • Module content:

    Simple applications of the first and second laws of thermodynamics. The concepts of work, heat, enthalpy and entropy. The calculation of internal energy, enthalpy and entropy using the equations of state. Simple heat engine cycles. Refrigeration and gas liquefaction. Process efficiency by means of energy. Introduction to non-ideality in VLE and mixing behaviour.

    View more

  • Module content:

    Transient response phenomena in RC, RL and RLC circuits: Natural response and step response. Alternating current (AC) circuits: Phasors, impedances, and power in AC circuits. The application of Ohm’s law, Kirchoff’s circuit theorems, matrix methods, and Thevenin and Norton equivalents to sinusoidal steady-state analysis. Three-phase circuits: Balanced three-phase circuits, star/delta configurations, and three-phase power transfer calculations. Magnetically coupled circuits: Mutual inductance, coupling factor, transformers, ideal transformers and autotransformers. Application of circuit theory to induction motors: basic principles of induction motors, equivalent circuit and analysis thereof, calculation of power and torque through application of Thevenin's theorem. Synoptic introduction to other types of motors.

    View more

  • Module content:

    Spreadsheet applications: Formulas and calculations, named ranges, plotting and trend lines, goal seek, linear programming, importing and exporting data, data navigation and filtering. Programming fundamentals: Names and objects, conditional and unconditional looping, branching, functions, modules, packages, reading and writing data files, graphical output (plotting). Solving simple problems using a high level programming language to develop, code and debug programs. Solving complex problems by breaking it down into a number of simple problems using concepts such as functions, modules and available packages. Programming principles are developed through solving mathematics and physics problems.

    View more

  • Module content:

    Concept of Stress: Stresses in structural members, stress on oblique plane and stress under general loading, components of stress, design considerations. Stress and Strain: statically indeterminate problems, thermal effects, Poisson’s ratio, generalised Hookes Law, shearing strain, stress-strain relationships. Torsion: Torsion of circular bars, stresses and strains in pure shear, power transmission, and statically indeterminate torsional members. Pure Bending: symmetric members in pure bending, stresses and deformations, deformations in transverse cross-sections, members made of composite materials, eccentric axial loading. Analysis and Design of Beams for Bending: shear and bending moment diagrams, relationships between load, shear and bending moments, design of prismatic beams for bending. Shearing stresses in Beams and Thin-Walled Members: Horizontal shearing stresses in beams, shearing stresses in Thin-Walled members. Transformation of Stress and Strain: Plane stress transformation, Mohr’s circle, principal stresses, maximum values and stress variation in prismatic beams; Plane strain transformation, Mohr’s circle, principal strains, maximum values, general state of stress, stresses in Thin-Walled pressure vessels. Principal Stresses under a given Loading: Principal stresses in beams, design of transmission shafts, stresses under combined loads. Deflection of Beams: Deformation under transverse loading, statically indeterminate beams, method of superposition. Energy Methods: Strain energy, elastic strain energy, strain energy for a general state of stress.
     

    View more

  • Module content:

    Linear algebra, eigenvalues and eigenvectors with applications to first and second order systems of differential equations. Sequences and series, convergence tests. Power series with applications to ordinary differential equations with variable coefficients. Fourier series with applications to partial differential equations such as potential, heat and wave equations.

    View more

  • Module content:

    Theory and solution methods for linear differential equations as well as for systems of linear differential equations. Theory and solution methods for first order non-linear differential equations. The Laplace transform with application to differential equations. Application of differential equations to modelling problems.

    View more

Minimum credits: 145

Core modules

  • Module content:

    The purpose of this module is to develop knowledge and understanding of engineering management principles and economic decision-making so that students can design, manage, evaluate and participate in engineering projects in the workplace. As such elements from engineering economics, project management and systems engineering are combined.
    This module develops and assesses the students’ competence in terms of ECSA Exit Level Outcome 11 relating to Engineering Management.

    View more

  • Module content:

    Characterisation and taxonomy of biological material. Biochemistry and the chemistry of life. Biological growth requirements, metabolism, growth kinetics and product formation. Enzyme chemistry and kinetics, basic stoichiometry of biological reactions as well as mass - and energy balances for these processes using a chemical engineering approach. Biological reactor, operation and downstream processing.

    View more

  • Module content:

    Steady and unsteady state conductive heat transfer in one to three dimensions.  Temperature distributions. Convective heat transfer. Application of boundary layer theory. Determination of film coefficients. Design of heat transfer equipment.  Radiant heat transfer. Application of the mechanical energy balance to single phase Newtonian fluids in steady state systems. Adjustment for multiphase, non-Newtonian as well as pulsating systems. Orifice design. Optimal economic choice of pipe diameters, pumps and control valves.

    View more

  • Module content:

    Fundamentals of phase and chemical equilibrium with emphasis on vapour/liquid systems leading to the study of separations and reacting systems. Concepts and formalism of thermodynamics. Postulates and laws of thermodynamics. Thermodynamic functions (enthalpy, entropy, Gibbs free energy). Thermochemistry and Ellingham diagrams. Phase Equilibria: Phase diagrams of single substances, phase boundaries, the Phase Rule. Phase diagrams of mixtures, steam distillation, eutectic mixtures. Solution thermodynamics: Ideal and non-ideal solutions, excess properties and activity coefficient models. The equations of state of ideal and real gases, residual properties and fugacity. Vapour-liquid equilibrium from equations of state and the approach. Application of thermodynamics to equilibrium between fluid- (gas and liquid) and condensed (liquid and solid) phases. Chemical reaction equilibrium.

    View more

  • Module content:

    Effective communication with engineering and technical audiences, as well as with the community at large, is taught. The emphasis is on written documentation. Formal communication is characterised by: the use of appropriate language and style; effective structuring of information; the use of modern electronic communication technologies, with emphasis on word processing, spreadsheets, appropriate email protocols, effective use of graphic information, effective and correct presentation of numerical data, correct referencing methods, seamless inclusion of mathematics expressions, tables, diagrams and appendices in written work; appropriate methods for levelling communication to the requirements of the target audience.

    View more

  • Module content:

    Batch reactors; basic reaction kinetics; fitting of experimental reaction data;  flow reactor basics.

    View more

  • Module content:

    Laboratory safety and general industrial safety practices. Techniques for planning of experiments. Experimental work illustrating: Analysis: Composition of coal and gas, heat of combustion, viscosity. Mass transfer: Gas absorption, batch distillation, azeotropic distillation, fractional distillation and liquid-liquid extraction. Heat transfer: Condenser, shell and tube heat exchanger, heat loss from insulated pipes. Piping system design: Frictional energy loss through pipes and fittings. Measuring equipment: Rate of flow, temperature. Reporting of laboratory results.

    View more

  • Module content:

    Separation by means of equilibrium stages. Design of flash distillation systems, distillation columns, absorbers and strippers by hand and computer calculations. Design of membrane separation systems.

    View more

  • Module content:

    Momentum transfer. Fluid statics. Control volume approach for conservation of mass, energy, and momentum. Application to pumps and turbines. Navier-Stokes equations, derivation and applications. Laminar and turbulent boundary layer theory. Heat transfer: fundamentals of heat transfer. Differential equations of heat transfer. Steady state conduction. Introduction to unsteady state conduction. Convection heat transfer and the thermal boundary layer. Radiation heat transfer. Mass transfer: fundamentals of mass transfer. Diffusion and the diffusion coefficient. Differential equations of mass transfer. Steady state molecular diffusion in one or more dimensions.

    View more

  • Module content:

    Application of the continuity equations, transport equations and phase relationships to describe time-dependent behaviour of processes. Linearisation and use of transfer functions.  Stability analysis, effect of dead time and inverse response. Elements of a control loop. Control principles and mechanisms.

    View more

  • Module content:

    *Attendance module only
    At the end of the second year of study, students in Chemical Engineering undergo at least six weeks of prescribed practical training in the industry. The student must also attend all excursions organised during the year by the department. A satisfactory report on the practical training must be submitted to the Faculty Administration within one week of registration. In exceptional circumstances the prescribed minimum period can be reduced, as approved by the Chairman of the School of Engineering.

    View more

  • Module content:

    Two exit-level Graduate Attributes (GAs) of ECSA are addressed and each must be passed in the same semester. GA7: Demonstrate critical awareness of the impact of engineering activity on the social, industrial and physical environment. The history of engineering globally and in South Africa. Most important engineering projects globally and in South Africa. The impact of technology on society. Occupational and public health and safety. Occupational Health and Safety Act. Impacts on the physical environment. The personal, social, cultural values and requirements of those affected by engineering activity. The combination of social, workplace (industrial) and physical environmental factors are appropriate to the discipline of the qualification. GA8: Demonstrate competence to work effectively on a small project as an individual, in teams and in multidisciplinary environments. Identifies and focuses on objectives. Works strategically. Executes tasks effectively. Delivers completed work on time. Effective teamwork: Makes individual contribution to team activity; performs critical functions; enhances work of fellow team members; benefits from support of team members; communicates effectively with team members; delivers completed work on time. Multidisciplinary work by the following: Acquires a working knowledge of co-worker’s discipline; uses a systems-engineering approach; communicates across disciplinary boundaries. Report and presentation on team project. Tasks require co-operation across at least one disciplinary boundary. Students acquire a working knowledge of co-worker’s discipline. Students communicate between disciplinary boundaries.

    View more

Minimum credits: 145

Core modules

  • Module content:

    Humidification and dehumidification of air. Water cooling, drying, crystallisation, ion exchange, particle technology, particle movement in a fluid, sedimentation. Hydrocyclones, flotation, filtration. Centrifuges. Fluidised bed technology. Mixing. Comminution. Pneumatic transport.

    View more

  • Module content:

    Dynamic properties of equipment, instruments and processes. Mathematical modelling and computer simulation of processes in the time, Laplace and frequency domains. Linearisation and non-linear processes. Stability of control systems. Controller tuning. Methods for process identification. Digital process control. Z-transforms. Use of computers and microprocessors. Introduction to modern control theory: state-space approach. Applied process control. Choice of control instrumentation. Plantwide control strategy. Development of P and IDs.

    View more

  • Module content:

    Application of chemical engineering principles for the complete design of a chemical plant.

    View more

  • Module content:

    Design economics and process evaluation. Cost estimation and time-value of money. Control applications, choice of instrumentation and development of a plantwide control strategy. Development of PandID’s. Safety: Site plan and layout, area classification, hazard and operability analysis (HAZOP). Occupational Safety and Health Act, Engineering Profession of South Africa Act. Requirements to maintain continued competence and to keep abreast of up-to date tools and techniques. ECSA code of conduct, Continuing Professional Development, ECSA outcomes, ECSA process and reasons for registration as PrEng. Displays understanding of the system of professional development. Accepts responsibility for own actions. Displays judgment in decision making during problem solving and design. Limits decision making to area of current competence. Reason about and make judgment on ethical aspects in case study context. Discerns boundaries of competence in problem solving and design. Case studies typical of engineering practice situations in which the graduate is likely to participate.

    View more

  • Module content:

    Development of new processing plants; Evaluating process alternatives; Developing a process flowsheet using a process synthesis approach. Applying thermodynamic principles to obtain an optimal synthesis route. Applications using computer packages.

    View more

  • Module content:

    Pinch analysis and exergy analysis. Optimisation techniques. Flowsheet optimisation. Economic evaluation of processes. Applications using computer packages.

    View more

  • Module content:

    *Attendance module only
    At the end of the third year of study, students in chemical engineering undergo at least six weeks of prescribed practical training in the industry. The student must also attend all excursions organised during the year by the department. A satisfactory report on the practical training must be submitted to the department within one week of registration. In exceptional circumstances the prescribed minimum period can be reduced, as approved by the chairman of the School of Engineering.

    View more

  • Module content:

    Heterogeneous catalysis: diffusion in reaction for catalyst pores and different catalyst geometries. Inter and intraparticle heat and mass transfer processes. Reactor design: energy and continuity equation for different types of reactor: stirred tank, pipe, radial flow, slurry and fluidised. Modelling of non-ideal flow in reactors.

    View more

  • Module content:

    The execution of a complete literature study and research project on a chosen subject.

    View more

  • Module content:

    Interpretation of the research results of CSC 411. The writing of a project report and scientific article.

    View more

  • Module content:

    A module to be selected from the list of available specialisation topics, including Process Control, Chemical Product Design, Environmental Engineering, Nuclear Engineering, Polymer Processing, Reactor Design, and Water Utilisation Engineering.

    View more


The regulations and rules for the degrees published here are subject to change and may be amended after the publication of this information.

The General Academic Regulations (G Regulations) and General Student Rules apply to all faculties and registered students of the University, as well as all prospective students who have accepted an offer of a place at the University of Pretoria. On registering for a programme, the student bears the responsibility of ensuring that they familiarise themselves with the General Academic Regulations applicable to their registration, as well as the relevant faculty-specific and programme-specific regulations and information as stipulated in the relevant yearbook. Ignorance concerning these regulations will not be accepted as an excuse for any transgression, or basis for an exception to any of the aforementioned regulations.

Copyright © University of Pretoria 2024. All rights reserved.

FAQ's Email Us Virtual Campus Share Cookie Preferences